How to Service a BISON 2000A Diesel Heater (Step-by-Step Video Guide)

How to Service a BISON 2000A Diesel Heater (Step-by-Step Video Guide)

Servicing a diesel heater sounds intimidating until you've done it once. It's about an hour of work with hand tools, and it's the single thing that most affects how long your heater lasts.

This guide walks through a full service on a BISON 2000A using the maintenance kit: new burner assembly, new glow pin, and both gaskets. The video shows every step — the text below follows the same order so you can read first, then follow along.

Before You Start

Get the right kit for your voltage. This matters more than anything else on this page:

  • GC6113 — 12 volt heaters
  • GC6114 — 24 volt heaters

The kit contains a new burner assembly, blower gasket, burner gasket and glow pin. All four are replace-only parts. Never reuse the old ones, even if they look serviceable — a reused gasket is the most common cause of a service that ends in a leak or a fault code.

Then make sure the heater is:

  1. Off — not standing by, fully off
  2. Fully cooled down, with the cool-down cycle finished
  3. Disconnected from power

Tools you'll need: a screwdriver set, hex keys for the M4 and M5 cap head screws, and a small pick for the gasket and alignment work. A small container for the screws saves a lot of time.

When to Service

Service every 800 to 1,000 run hours. The controller's information screen shows your total hours, so you don't have to guess — our OLED thermostat guide shows where to find it.

A D3 code on the controller is the heater telling you it's due. Our error code guide covers what that and every other code means.

You'll also want a service sooner if the heater has been short cycling, running mostly on its lowest setting, or has started failing to ignite on cold mornings. All three point to carbon build-up, which is what this service clears.

Taking It Apart

1. Open the case

Remove the end hoods, then lift off the top cover.

Take out the red grommets and put them somewhere safe — they go back on at the end. Then slide off the heat exchanger housing to expose the heater core.

2. Remove the cabin air impeller

Turn the unit over and pull the cabin air impeller off the motor shaft.

3. Disconnect the ECU

Unplug the glow pin, overheat sensor and blower connectors from the ECU.

Pull on the connectors, never the wires. A damaged connector turns a routine service into a parts order.

Then take out the screws holding the ECU, lift it off and set it aside.

4. Remove the blower motor

Take out the M5 cap head screws and keep them together so none go missing.

Lift the blower off and peel away the old blower gasket. Throw it away — it's in the kit for a reason.

5. Remove the burner

Lay the heat exchanger on its side and unclip the glow pin lead from the side of the housing. Stand it back up and remove the M4 burner screws.

This is the step worth watching rather than reading. Use a small pick to gently pry the burner and gasket loose from the heat exchanger, then pull the old burner assembly straight out along with the burner gasket. Both get replaced.

Remove the flame tube. While it's out, check the flame tube and the inside of the heat exchanger for carbon build-up and clean them if needed. This is your chance to see how your heater has been running: heavy carbon means too many short runs on low settings.

Set the old burner and glow pin aside. From here on, only new parts go back in.

Putting It Back Together

6. Fit the new glow pin

Take the new glow pin from the kit and fit it into the new burner assembly. Secure it — snug is enough, don't over-tighten.

7. Refit the flame tube

Put the flame tube back into the heat exchanger and make sure it's centred.

8. Fit the new burner and gasket

Fit the new burner gasket from the kit, then insert the new burner assembly, routing the glow pin and sensor leads as you go.

Use a pick to line up the screw holes in the burner and gasket with the heat exchanger. Another one to watch rather than read — the alignment is fiddly the first time and obvious once you've seen it done.

Refit the M4 burner screws, tightening them evenly in a cross pattern so the new gasket seals all the way around. An uneven gasket is a leak waiting to happen.

9. Reconnect the glow pin lead

Turn the unit on its side and clip the glow pin lead back into place along the housing.

10. Fit the new blower gasket and blower

Fit the new blower gasket — again, never the old one. Line the blower up with the burner, set it in place, and refit the M5 blower screws, tightening evenly.

A good seal here keeps combustion air flowing properly, which is what keeps the burn clean.

11. Refit the ECU and connectors

Put the ECU back in position and screw it down. Reconnect the glow pin, overheat sensor and blower connectors.

Make sure each one is pushed all the way in and fully seated. A partly seated connector produces a sensor fault code that sends people chasing a failed part that isn't failed.

12. Close it up

Slide the cabin air impeller back onto the motor shaft and secure it. Refit the red grommets onto the heat exchanger. Fit the heat exchanger housing back over the core, slide the top cover on, and refit the end hoods.

Reconnect power and fuel, and your BISON 2000A is ready to run.

The First Run After a Service

  1. Check your fuel connections before powering up
  2. Let it complete a full cycle, including cool-down — never cut power mid-run
  3. Expect a little smoke on the first burn as new parts settle in
  4. Listen for a steady fuel pump tick. An irregular tick means air in the line
  5. If a fault code appears, check the error code guide before ordering parts — most post-service codes are a connector that isn't fully seated

Making the Next Service Easier

The biggest factor in how much carbon you find next time is how you run the heater:

  • Give it a long, hot run regularly — 30 minutes or more at a high setting, even in mild weather. That's what burns off deposits
  • Avoid constant short runs on the lowest setting. It's the fastest way to carbon up a burner
  • Keep the battery healthy. Low voltage at startup causes more faults than any worn part
  • Use winter-grade diesel in cold weather, since summer diesel can gel

Our maintenance checklist covers the between-service routine.

Watch the Full Service

Every step above is demonstrated in the video, including the three that are much easier to see than to read: prying the old burner loose, lining up the burner screw holes, and seating the ECU connectors.

Watch: BISON 2000A maintenance, start to finish →

Frequently Asked Questions

How often should I service my BISON 2000A?

Every 800 to 1,000 run hours. The controller's information screen shows your total hours. A D3 code on the controller is the heater telling you it's due.

Which maintenance kit do I need?

GC6113 for 12 volt heaters and GC6114 for 24 volt heaters. Check your heater's voltage before ordering — the kits aren't interchangeable.

What's in the BISON 2000A maintenance kit?

A new burner assembly, blower gasket, burner gasket and glow pin. All four must be replaced with new parts at every service.

Can I reuse the old gaskets if they look fine?

No. Gaskets compress and take a set once they've been through heat cycles, so a reused gasket won't seal reliably even when it looks undamaged. A poor seal at the burner or blower leads to incomplete combustion and fault codes.

Can I service a diesel heater myself?

Yes. It's hand-tool work with no special equipment, and it takes most people an hour or two the first time. Follow the video, keep the screws organised, and don't reuse any part the kit replaces.

Why is my heater failing to start after a service?

The usual cause is a connector that isn't fully seated, or air drawn into the fuel line. Check that the glow pin, overheat sensor and blower connectors are pushed all the way in, then check for a steady fuel pump tick.

What if I find heavy carbon build-up?

Clean the flame tube and the inside of the heat exchanger while the burner is out. Heavy carbon usually means the heater has been running short cycles on low settings — regular long runs at a higher setting will keep the next service cleaner.


Get the Parts

BISON 2000A Maintenance Kit — GC6113 for 12 V, GC6114 for 24 V

Not sure which you need, or hit something the video doesn't cover? Call 1-800-517-7740 (Mon–Fri, 9 AM–5 PM PT) or email info@generalcomponents.ca.

All BISON 2000A parts · Installation guides · Find a dealer

Always follow the manual for your specific model and voltage.

Back to blog